DARK MATTER - 9 BALLS - SI3N4 - FULL CERAMIC R188 - (Single Piece Not a Pack)
Notice 1: All orders are final for this product.
All the characteristics described below, (except for "specs") are based on our personal opinions only. Features such as "speed" or "sound" may vary drastically, depending on which spinner you are spinning and on each person. Please, keep that in mind once you read the characteristics below :)
CHARACTERISTICS:
* Feedback: Very strong and pleasant spins.
* Sound: Strong and very pleasant whir "ceramic sound".
* Speed: Very fast and long spin times.
* Tolerance: "3" in a scale from 0 - 5, being 0 loose, and 5 tight)
SPECS:
* 9 Balls - Ceramic Silicon Nitride (Si3N4)
* Full Ceramic
* One-Piece "Snap In" PEEK Crown Cage
::
Warning!
Ceramic bearings can break! In case your bearing breaks during installation or removal, we do not offer replacements or refunds, so be very careful when installing or removing them, and pay attention to the following:
Be careful when installing or uninstalling ceramic bearings as they may break if your spinner bearing hole is too tight for them. Ceramic is a very brittle and hard material and it has no room to flex or bend. If the bearing hole of your spinner is too tight, i.e if it has too much glue, or dry glue leftover from a previous installation, or if your spinner was machined with a bearing hole slightly smaller than the standard, it is very important that you do not force push your bearing in or out. If you feel a strong resistance when installing or removing your ceramic bearing, stop immediately. You may want to make sure your bearing hole is very clean, with no glue residues before installing your bearing. If glue is necessary then you may apply a little bit of glue in the spinner bearing hole walls (never on the bearing) and try again. If you still feel it’s too tight for your ceramic bearing, do not install it on that spinner. Again, we do not offer replacements or refunds if you break your bearing!
Attention: When using any type of glue to install your bearings, be very careful not to drop any small drop of glue inside the bearing tracks. Also pay attention to small flakes of dry glue once you are installing or uninstalling your bearings as they may fall into the bearing tracks and could potentially ruin your bearing spins. We QC and spin test every bearing before they leave the Shop to make sure they spin nice and freely, and we do not take responsibility for user error, nor issue replacements for this reason. If you have any questions on how to install your bearings please contact us and we would be glad to help!
Notice 2: Due to the ceramic materials and the manufacturing techniques used to make this specific bearing, it’s is common for the bearing to present small imperfections such as small marks on its body and cage. The PEEK cage slots may have slightly different sizes or offset. However, all these are considered normal characteristics for this bearing, and they should not affect the performance and spin quality of the bearing in any way.
If you encounter small marks like nicks and dings around the edges of the races, please know that this is normal for this specific bearing.
UQH does not consider any of these as "issues" and no refunds or cancellations are provided for bearing orders, unless the bearing is malfunctioning. More infos can be found in our refund and return policy page.
Notice 3: Please notice that we visually check every single bearing before they ship as well as test them for tolerance and give them a quick spin to make sure they are performing well and spinning freely.
Some bearings may be a bit dusty or gritty once you receive them, or sometimes they may present small marks or tiny dings on the edges of the races (specially for full ceramic ones due to the brittleness of the material), but they should not have any mechanical faults.
For bearings that you may feel that are "dusty", please use a compressed air can on the bearing while holding it with a straw. Make sure to make the bearing spin as fast as possible for around 5 seconds. That should be enough to get rid of any tiny particles, dust or lint that may be sitting between the bearing balls and cage. We do not recommend the use of liquids or soap for any bearings.
At this time, we do NOT offer refunds for bearings (unless there is clear mechanical or manufacturing fault upon receiving them) and all orders are final. If you have any questions please email us or visit our “Refund & Return Policy" page.